Liste des Groupes | Revenir à rb tech |
On Fri, 30 Aug 2024 14:01:11 -0500, AMuzi <am@yellowjersey.org> wrote:I wonder if the adoption of Torx has reduced that problem.
On 8/30/2024 1:28 PM, cyclintom wrote:I'll tell you a secret. Probably the most common job that aOn Thu Aug 29 11:50:12 2024 John B. wrote:>On Wed, 28 Aug 2024 16:17:48 -0700, Jeff Liebermann <jeffl@cruzio.com>>
wrote:
>On Wed, 28 Aug 2024 23:02:03 GMT, cyclintom <cyclintom@yahoo.com>>
wrote:
>Then perhaps you missed the part where he thought it funny that I could learn science by reading out three entire non-fiction sections of Oakland libraries?>
I think your claim is hilarious:
06/07/2022
<https://groups.google.com/g/rec.bicycles.tech/c/QNPNSofg064/m/Xaamy15iBQAJ>
"I would warrant that I've read more than 20 times more books than you
have. I read out three public libraries, the military library and all
of the books I used to gain the knowledge to become an engineer."
>
How did the "three public libraries" magically morph into "three
entire non-fiction sections of Oakland libraries"? Also, what
happened to the military library you claim to have "read out" whatever
that means? Tom, you really should write down your lies so that you
don't screw up this badly trying to remember them.
>... from a point of NEVER working in the Telephone industry he denies that "light line" means fiber optics to installers.>
12/23/2021
<https://groups.google.com/g/rec.bicycles.tech/c/_1eEehgsDD0/m/cgRIn7ofDQAJ>
"Do you think that you're impressing people using the term "fiber
optics" when the common term is light lines and even AT&T is using
it?"
>
Show me where AT&T is using the term "light lines" to refer to fiber
optical cable used for communications (not for decorative
illumination).
>he has plainly never used a good oscilloscope so he doesn't know why you would use pulse width modulation to measure wire length.>
You've been asked to explain how to use PWM to "test cables" many
times. Nobody asked about measuring wire length.
12/23/2021
<https://groups.google.com/g/rec.bicycles.tech/c/_1eEehgsDD0/m/t0uJbEMbDQAJ>
"I'm not explaining anything to someone so stupid that they don't know
why you use pulse width modulation to measure loses due to line shorts
which is the failure mode of coax."
<https://groups.google.com/g/rec.bicycles.tech/c/_1eEehgsDD0/m/bIkgkvkKDQAJ>
"Using PWM to test extremely long cables is common practice."
Re Tommy's "military library". The air force has several types of
Libraries. (1) The public library for readers just like your home town
has. (2) A library of regulations that covers every thing on how to
confirm how many eat supper in the Mess hall to when may a dentist
insist in pulling a tooth. and then there is (3) the vast technical
library that tells you every thing you need to know about any
technical (airplane, truck, whatever, even airport runways) device
that you need fir help in repairing installing removing) any device in
the inventory - I once found a reference for the size bolts to use in
a missile retaining device on a B-52 :-)
>
So Tommy's claim to have read the military library is akin to saying
that the moon really, truly, IS blue cheese
-- Cheers,
>
John B.
>
>
>
>
Proving that John never set foot in a military library. That must be how he got his diaphonous A&P. For the brightest apprintice that is two years and John is hardly bright or they wouldn't have made him crew chief which was nothing more than paperwork.
Are you being purposefully obtuse? Every AFB has a machine
shop, as do Navy ships. Some are bare bones, some are world
class machining facilities, Tinker AFB for example:
>
https://www.tinker.af.mil/News/Features/Display/Article/388818/parts-producers-tinkers-machine-shops-are-invaluable/
>
The AFB just down the road, Truax (across the highway from
FedEx dropoff), has a very nice shop. Supports F16 and F35
which pass over most afternoons to Camp McCoy bomb range.
Machinist, in the Air Force, does is remove "bad" screws. An airplane
is full of panels that need to be removed to get at something that
needs repair and all these panels are held on by "screws", actually
"Machine Screws". ands, as a general statement, are removed by
electrical/electronic craftsmen in order to do their work.
Now electrical/electronics craftsmen, in the Air Force are normally
the product of a "Tech School" that the Air Force uses to turn some
blundering idiot right off the street into a competent craftsman who
can be of benefit to the A.F.'s mission.
(there are some "tech" schools, although not electronic, that are 2
year, or longer in duration.)
But in spite of all this training the A.F., for some reason, neglects.
perhaps the most common task there E/E people do. Removing screws so
that they can get to the "Gizmo" that has to be replaced. The use of a
screwdriver, and thusly in addition to the electric gizmo the project
turns into a fix all the damaged screws so the panel can be replaced
and someone has to go out in the wind and the cold to rectify the "F-
- k Ups". And that is the Machinist :-)
Les messages affichés proviennent d'usenet.