Re: OT: sound speed depends on frequency on mars

On 1/09/2024 12:18 am, john larkin wrote:

On Sat, 31 Aug 2024 16:17:39 +1000, Bill Sloman <bill.sloman@ieee.org>
wrote:
 

On 31/08/2024 3:10 am, john larkin wrote:

On Sat, 31 Aug 2024 01:23:19 +1000, Bill Sloman <bill.sloman@ieee.org>
wrote:
>

On 31/08/2024 12:34 am, john larkin wrote:

On Fri, 30 Aug 2024 11:13:05 GMT, Jan Panteltje <alien@comet.invalid>
wrote:
>

NASA's Mars rover Perseverance has found that sound travels much more slowly on the Red Planet than it does on Earth
and behaves in some unexpected ways that could have strange consequences for communication on the planet.
https://www.space.com/nasa-mars-rover-perseverance-speed-of-sound#main
    At frequencies above 240 Hertz, "the collision-activated vibrational modes of carbon dioxide molecules do not have enough time to relax, or return to their original state,"
    the researchers said, which results in sound waves at higher frequencies traveling more than 32 feet per second (10 m/s) faster than the low-frequency ones.
    That means that if you were standing on Mars, listening to distant music, you would hear higher-pitched sounds before you would hear the lower-pitched ones.
>
paper:
https://www.hou.usra.edu/meetings/lpsc2022/pdf/1357.pdf
>
So...
Music from far away may sound funny?
>
For Mars we will need compensation headphones with distance measurement and variable delays....
;-)
>
Better use radio.. and earplugs/ headphones...

>
Funny, I just delivered a lecture on transmission lines and noted that
microstrips have dispersion from  the unbalanced dielectric constants
and skin effect. Rising edges get sloppy at the and of a long trace.

>
I hope you pointed out that buried strip-line isn't dispersive. I have
pointed this out here from time to time.

>
Of course it's dispersive, maybe a bit less than microstrip.

>
Why do you think that?

 Because dielectrics are imperfect, especially FR4, and because there
are lots of papers online that analyze dispersion in stripline.

But you can't cite any of them. You wouldn't use FR4 around a stripline if you wanted a low-dispersion transmission line. There are better substrates his frequency work.

It's hard to keep up decent impedances on stripline in a multilayer
board, especially 8 or 10 layers.

>
Stripline is buried between two ground planes. The only tricky part of
impedance control is the thickness of the dielectric in the two layers
above and below the strip-line. In a ten layer board this is thinner
than it would be in a board with fewer layers.

 And eventually the trace has to be skinnier than PCB houses are
willing to etch.

Why?

Standard pricing seems to be around 5 or maybe 4 mils
width these days. We do a lot of 5, to sneak between BGA balls, but
sometimes even 5 is too big.
 Thin dielectrics have tolerance issues too. I'm talking about real
PCBs here, not ideal theoretical stuff.

Printed circuit board are always real.

Pay enough for close-tolerance substrates in the two relevant layers and
you should be okay.

 "Pay enough" can get crazy fast. I don't want to pay hundreds of
dollars for a smallish PCB.

An eight or ten layer PCB isn't going to be small. You only need lots of layers when you have to connect lots of stuff.

https://www.wevolver.com/article/stripline-vs-microstrip
>

I wonder if anyone has added surface-mount Heaviside loading coils to
a PCB trace.
>
https://en.wikipedia.org/wiki/Loading_coil

>
It would be a bit silly.

John snipped the rest of that senstence, without marking the snip.
 >>>> You can make lumped constant transmission lines by linking a series >>>> of capacitors with discrete inductors, if you want a high impedance >>>> transmission line - people sold them as thick film hybrid
 >>>> assemblies, and I even used a few, a very long time ago.

>
Most ideas seem silly to people who are by nature hostile to ideas.

>
Not a problem I've got.
>

Dismissing is easier than thinking.

>
Thinking about what a loading coil might be doing to the impedance of a
PCB trace isn't something that you seem to have managed to do.

 I certainly had the idea.

In a remarkably half-baked way.

I might Spice a bunch of ltlines with
inductors between, just for fun. It's unlikely that I'd use such an
arrangement in real life, but it's just possible, especially if analog
quality of a fast edge matters, like in a laser modulator maybe. It's
preferable to just keep all the traces very short, but that's not
always possible.

You seem to be intent on re-inventing the lumped constant delay line, without being aware that they were commercially available some thirty years ago, back when I used them. They may still be available.
Back around 1985 we planned on making one of our own when we wanted a microsecond or so of pure delay on the main signal to synchronise it with the small second order corrections we were adding in from a couple of analog multipliers (which had their own propagation delay).
--
Bill Sloman, Sydney