Re: Francophones

On Sat, 21 Dec 2024 21:31:51 +0100, Jeroen Belleman
<jeroen@nospam.please> wrote:

On 12/21/24 14:57, Cursitor Doom wrote:

On Sat, 21 Dec 2024 08:57:51 +0000, liz@poppyrecords.invalid.invalid
(Liz Tuddenham) wrote:
 

Cursitor Doom <cd@notformail.com> wrote:
>

On Sat, 21 Dec 2024 00:05:08 +0100, Jeroen Belleman
<jeroen@nospam.please> wrote:
>

On 12/20/24 22:16, Cursitor Doom wrote:

On Fri, 20 Dec 2024 19:32:14 +0000, liz@poppyrecords.invalid.invalid
(Liz Tuddenham) wrote:
>

Cursitor Doom <cd@notformail.com> wrote:
>

Do we have any French speakers on the Panel? I have a radio that's
badly in need of realignment and the only instructions I can find are
a set in French. I can't use Google translate because they've used too
many abbreviations in the text and they won't parse any sense.

>
I'm not a particularly fluent French speaker, but I could probably sort
out some technical instructions in French   If you want to send them to
me, I'll have a go (you should be able to work out my e-mail address).

>
Many thanks indeed for your kind offer. I suspect it will probably
require a native French speaker to decypher, but who knows?  :-)

>
I'm not a native French speaker, but I may be able to help anyway.
Fire away.

>
Well that's interesing as I had did think you might respond given some
of the background you've revealed here in the past. I don't have the
relevant page here right now, but will make it available tomorrow. It
is only the one page and only one column of that, so nothing too
onerous. I did show it to a genuine French chum of mine a few weeks
ago, but he was stumped by the technical side of it and couldn't
assist much, unfortunately. So it appears it needs someone who can
speak French fluently *and* understands the process of radio
alignment. I kind of guessed that might be you....

>
>
Many years ago Practical Wireless published an article about the French
819-line high-definition television service which had been translated
from French by someone who knew nothing about television or radio
terminologyy.  It was hilarious nonsense but I eventually managed to
translate it back into French so that I could understand it.
>
If you post your text here, we can all have a go at it.

 
Sorry for the delay; took a bit of tracking down but I have it now:
 
https://disk.yandex.com/i/3SiZ6rN_k-fP4w
 
It's only page 1 that needs the translation - and of that, in
particular the abbreviated bits. I haven't read French since I was in
school about a hundred years ago, so it's all Dutch to me. :-)

>
>
This was translated from German into French by someone who also
did not know clearly what it all meant. Not everything makes
perfect sense.
>
Also, while it doesn't say so, many of the adjustments interact,
so you may have to go back and forth a few times. Anyway, here
goes.
>
Jeroen Belleman
>
>
===============================================================
>
-- DC current adjustments (for 9V supply)
   - Adjustment of the push-pull audio stage:
   Cut the solder bridge marked -x- in the collector trace of the
   AC188 T11 and insert a current meter. Adjust R410 for 6.5mA.
   Restore the bridge.
   - Adjustment of the IF amplifier:
   Set R515 to obtain 1.35V across T4's emitter resistor R518.
>
-- Adjustment of the FM-IF stages. The radio should be set to "FM".
   Connect a wobbulator centered on 10.7MHz at MP5 and the diode
   detector shown at ZF VII (I think...) MP6. Detune ZF VIII (a).
   Then tune ZFVII (b) for a symmetrical maximum response.
   - Inject signal at MP3 and tune ZF VI (c) and ZF V (d) for
   symmetrical maximum response.
   - Inject signal on MP2 and adjust ZF IV (e) and ZF III (f) for
   symmetrical maximum response.
   - Inject a weakly coupled signal at the mixer (MP1?) and adjust
   ZF II (g) and ZF I (h) for symmetrical maximum response.
   - Discriminator: Inject signal at MP5, with a level low
   enough that no limiting occurs in the IF strip. Observe the
   signal at MP11 (audio amplifier input) with load impedance 50k.
   Adjust ZF VIII (a) for symmetrical response.
>
-- Adjustment of the AM IF (460kHz) stages. The radio should be
   set to "PO" (AM, 560-1450kHz). Connect a measurement instrument
   at MP4 (Weakly coupled).
   - Inject a wobbulator signal at MP3 and adjust ZF XIII and ZF XII
   for symmetrical maximum response.
   - Inject signal at MP8 and adjust ZF XI for symmetrical maximum
   response.
   - Inject signal at MP7 and adjust ZF X and ZF IX for symmetrical
   maximum response.
>
-- Adjustment of local oscillator and AM input. For short and
   medium wave, couple signal into the ferrite rod antenna using
   the frame. For short wave, remove the rod antenna and couple
   signal at the antenna connection through 15pF.
   Tune to 560kHz and adjust (1) and (3) for maximum response.
   Mixer sensitivity 13uV and oscillator output 60-90mV.
   Tune to 1450 kHz and adjust (2) and (4) for maximum response.
   - Set the radio to GO (Long wave, 160-240kHz).
   Tune to 160kHz and adjust (5) and (6) for maximum response.
   Mixer sensitivity 13uV and oscillator output 65-95mV.
   - Set the radio to OC (Short wave, 6.5-15MHz)
   Tune to 6.5MHz and adjust (8) and (10) for maximum response.
   Tune to 15MHz and adjust (9) and (11) for maximum response.
   Mixer sensitivity 5uV and oscillator output 35-90mV.
>
-- Adjustment of the FM LO. Signal from an RF generator with
   60 Ohm output impedance injected directly at the mixer (MP1?)
   with a loaded signal level <2mV. Set the radio to FM.
   - Tune to 88MHz and adjust (A) and (C) for maximum response.
   - Tune to 106MHz and adjust (B) and (D) for maximum response,
   Noise level is about 5 times kT0. Oscillator output voltage
   75-85mV (at T2's emitter).

Thanks, Jeroen. Geez, you just can't win with these bastards. I've got
a 50 ohm signal generator and a 70 ohm one - but that's not good
enough for 'em. No, they want me to splash out on a 60 ohm one and
where am I going to source one of those??
And it doesn't stop there! I thought all my vintage servicing voltage
reading requirements would be met when I bought an old analogue Avo
with 20kohms/volt. But now it seems I need to scratch around for a
500ohms/volt one. It seems they're expecting whoever services these
things to have access to an infinite range of test equipment to
satisfy whatever whim the manual compiler for the equipment had at the
time. <making overly theatrical gesture of despair>