Re: mountable power ports

Liste des GroupesRevenir à se design 
Sujet : Re: mountable power ports
De : blockedofcourse (at) *nospam* foo.invalid (Don Y)
Groupes : sci.electronics.design
Date : 26. Mar 2025, 17:40:51
Autres entêtes
Organisation : A noiseless patient Spider
Message-ID : <vs1amj$2546b$1@dont-email.me>
References : 1
User-Agent : Mozilla/5.0 (Windows NT 6.1; Win64; x64; rv:102.0) Gecko/20100101 Thunderbird/102.2.2
On 3/26/2025 8:56 AM, Christopher Howard wrote:
Hi, my project box is a large tin cookie box. I need to bring in +15V,
-15V, and GND lines from my external bipolar power supply. (I was
thinking I would have a separate bolt for the chassis ground, which
would go off to a big ground bus bar near my workbench.) For the three
lines from the power supply, I am wondering what would be the best (but
economical) choice for a power connector to mount into the side of the
project box. Something that sounded appealing was the spring speaker
terminal clips I see on Amazon, but the downside there is they only come
in pairs of two or four, rather than three, and they are color coded
red/black which does not quite make sense here. I am inclined to leave
the wires on the power supply itself bare on the end, rather than
attaching some specialty connector to those.
There's always the old benchtop standard of binding posts.
This provides the most flexibility in connection -- by providing
the least convenience!  :<  (you can buy dual banana plugs
to mate with a pair of appropriately spaced binding posts;
but, there is nothing to prevent you from plugging them
"upside down")
What sort of current carrying capacity do you require?
There are lots of three-pin connectors available -- especially
as your current handling requirements go down.
Note that you will likely want to require the connector to
be mated/unmated with power *off* if you have any concern
over power sequencing (as many connectors won't guarantee
which conductors(s) make/break first/last).
Round will be preferable as you can just use a drill to make
a clean hole (instead of needing a punch or resorting to a nibbler).
If other similar connectors might be prevalent "nearby", you
may want to avoid them (e.g., the ubiquitous barrel connectors)
to avoid the possibility of confusion between which cable end
mates with which device.
And, should consider how much mechanical security you want (need);
is there a risk that the connection may open if you are inclined to
move the box to some other location while powered?
I have been using a sturdy circular connector family for user-maintained
connections around the house, similar to this:
<https://www.theindustrymart.com/Upload/images/product/4-pin-metal-aviation-connectors-plugs-gx25-male-female-docking-cable-straight-circular-aviation-connector.jpg>
They are available with a variety of pincounts in the same basic
size.  The threaded collar ensures they can remain mated regardless
of orientation and (minor) tugs on the cables.
They are also large enough to make assembling/repairing a cable assembly
easy to do without special tools (as they have to be assembled and
repaired in the field).

Date Sujet#  Auteur
26 Mar 25 * mountable power ports27Christopher Howard
26 Mar 25 +- Re: mountable power ports1Lasse Langwadt
26 Mar 25 +* Re: mountable power ports20Don Y
26 Mar 25 i`* Re: mountable power ports19Liz Tuddenham
26 Mar 25 i +* Re: mountable power ports2Don Y
26 Mar 25 i i`- Re: mountable power ports1Don Y
27 Mar 25 i `* Re: mountable power ports16Christopher Howard
27 Mar 25 i  +* Re: mountable power ports14Liz Tuddenham
27 Mar 25 i  i`* Re: mountable power ports13Don Y
27 Mar 25 i  i `* Re: mountable power ports12john larkin
28 Mar 25 i  i  `* Re: mountable power ports11Liz Tuddenham
28 Mar 25 i  i   `* Re: mountable power ports10john larkin
28 Mar 25 i  i    +* Re: mountable power ports2Liz Tuddenham
28 Mar 25 i  i    i`- Re: mountable power ports1john larkin
28 Mar 25 i  i    +- Re: mountable power ports1Jeroen Belleman
28 Mar 25 i  i    `* Re: mountable power ports6Phil Hobbs
28 Mar 25 i  i     +* Re: mountable power ports3john larkin
28 Mar 25 i  i     i`* Re: mountable power ports2Jeroen Belleman
28 Mar 25 i  i     i `- Re: mountable power ports1john larkin
28 Mar 25 i  i     `* Re: mountable power ports2ehsjr
28 Mar 25 i  i      `- Re: mountable power ports1john larkin
27 Mar 25 i  `- Re: mountable power ports1john larkin
26 Mar 25 +* Re: mountable power ports3john larkin
26 Mar 25 i`* Re: mountable power ports2Lasse Langwadt
27 Mar 25 i `- Re: mountable power ports1john larkin
27 Mar 25 `* Re: mountable power ports2Martin Rid
27 Mar 25  `- Re: mountable power ports1John R Walliker

Haut de la page

Les messages affichés proviennent d'usenet.

NewsPortal